Get a quote

Opening Measuring Calculator for Aluminium Doors

A door made 10 mm too big doesn't fit, and one made 30 mm too small leaves gaps that leak. Measure the opening in six places and across both diagonals, then let the calculator work out the frame size to order.

T02 · Opening surveyUnits: mm · NTS
Smallest width
–
Smallest height
–
Frame order size
–
Out of square
–

All measurements in millimetres, brick to brick (or plaster to plaster) inside the opening. The order size is the smallest width and height less the fitting gap on each side.

Openings in brick and plaster are rarely perfectly straight. Measuring once in the middle is the most common reason a supply-only door doesn't fit. Fabricators measure the width at the top, middle and bottom and the height at both sides and the centre, then work from the smallest figure. This calculator does the same.

How to measure the opening

  • Width: measure between the brick or plaster reveals at the top, the middle and the bottom of the opening. Ignore any old frame; measure to the wall.
  • Height: measure from the finished floor or sill to the underside of the lintel at the left, the centre and the right.
  • Diagonals: measure from the top-left corner to the bottom-right corner, and from top-right to bottom-left. If the two match, the opening is square.
  • Use a steel tape and write every figure down in millimetres. Don't round to the nearest centimetre.

If the floor isn't finished yet, tell the installer the planned floor build-up (screed and tiles). A door frame must sit on the finished floor level or a threshold, and 20 mm of tiles can make a door too tall.

Why the frame is smaller than the opening

An aluminium frame needs a small gap around it so it can be packed level and square and sealed with silicone or a foam backer and sealant. Five millimetres per side suits a smooth plastered reveal; 8 to 10 mm suits rough or uneven brickwork. The frame sits directly on the sill or threshold, so the height is reduced at the top only. A gap much bigger than 10 mm is hard to seal neatly and lets water in on exposed walls.

Out-of-square and out-of-level openings

A difference of up to about 5 mm between the diagonals is normal. More than 10 mm means the opening is out of square. The installer still fits the frame square and level and packs the gaps, but the sealant joint will be wider on one side. Large differences usually point to a sagging lintel or a sill that isn't level, which is worth fixing before a new door goes in. See aluminium door installation for what a proper fitting includes.

Supply-only orders

If you are buying a standard-size door off the shelf, compare its overall frame size with the order size from the calculator. The frame must be smaller than the opening, not equal to it. If the nearest standard size leaves gaps bigger than about 15 mm, a door made to measure will look and seal better. Our installers can measure for you; mention it in your quote request.

Frequently asked questions

Do I measure the old frame or the wall?
Measure the wall opening (brick to brick or plaster to plaster) after the old frame comes out, or measure inside the old frame and add its sightline if it is still in. Installers re-measure the bare opening before making the door.
How much smaller than the opening should an aluminium door frame be?
Usually 5 to 10 mm less on each side and at the top. The frame sits on the sill or floor, so no gap is taken off the bottom.
What if my three widths are very different?
Use the smallest. Differences of more than 10 mm mean the reveals are out of line, and the installer will pack the frame and seal a wider joint on one side.
Will an installer still measure?
Yes. For a supply-and-fit job the installer always does a site measure, and the final dimensions are their responsibility. Your measurements help get an accurate quote before the visit.

More aluminium door tools

MarkDrawingToolWhat it does
T01Door Panel Layout CalculatorPanel count, panel width and clear opening for sliding, stacking, folding and French doors, drawn to scale.Open
T03Glass Weight and Roller CalculatorWeight of a glass door panel by size and glass type, and the roller rating it needs.Open
T04Safety Glass Checker (SANS 10400-N)Check whether a pane in a door, window, shower or shopfront must be safety glass.Open
T05Door and Window Schedule BuilderList every opening with size, type, colour and glass, then print it or send it as one quote request.Open
Get a free quote