Get a quote

Safety Glass Checker: SANS 10400-N for Doors and Windows

South Africa's building regulations say where glass must be toughened or laminated safety glass. Choose where the pane is and enter its size to see whether safety glass is required.

T04 · Glazing checkUnits: mm · NTS
Pane area
–
Safety glass
–
If ordinary glass
–

A guide based on the safety glazing requirements of SANS 10400-N (Glazing), as summarised for the public. It is not a substitute for the standard, the local authority's plan examiner or a glazier's specification.

Part N of the National Building Regulations (SANS 10400-N, Glazing) exists because people walk into glass, especially in doors, low windows and bathrooms. Safety glass either crumbles into small blunt pieces (toughened) or stays held together by its interlayer (laminated) when it breaks. This checker applies the main rules to a single pane.

Where safety glass is required

LocationRule
DoorsSafety glass for any pane over 1 m². A pane of 1 m² or less may be ordinary glass at least 6 mm thick.
Low-level glazingGlass less than 800 mm above the floor must be safety glass, or at least 6 mm ordinary glass if the pane is no bigger than 1 m².
Window sillsUnless there is a barrier, sills should be at least 300 mm above the floor.
Showers and bathsAlways safety glass.
ShopfrontsSafety glass for shop windows and shopfronts over 1 m².
Stairs, ramps and landingsSafety glass where glass is less than 1.8 m above the pitch line or landing.

In practice, almost every glazed aluminium door panel is bigger than 1 m², so sliding, stacking, folding and French doors are made with safety glass as standard.

Ordinary glass thickness by area

Where safety glass is not required, clear annealed float glass is chosen by the area of the pane:

Pane areaMinimum thickness
Up to 0.75 m²3 mm
0.75 – 1.5 m²4 mm
1.5 – 2.1 m²5 mm
2.1 – 3.2 m²6 mm

Exposure to wind, the height of the building and the way the glass is supported all affect the final thickness, so your glazier may specify thicker glass than this.

Toughened or laminated?

Toughened glass is heat-treated, about four to five times stronger than ordinary glass, and breaks into small granules. It can't be cut after toughening, so it is made to size. Laminated glass (6.38 mm is the usual door glass) is two sheets bonded with a plastic interlayer. It cracks but stays in the frame, which also makes it harder to break through and cuts out most UV. Many installers use laminated glass in doors for security and toughened in showers and frameless doors. Read more on our aluminium door glass page.

Marking and compliance

Safety glass should carry a permanent mark showing it meets the relevant South African standard. Large clear panes that people might not see, such as full-height glass doors and shopfronts, should also be made visible with a manifestation such as etched bands or decals. If your plans are being submitted to council, your architect or the glazier can provide the glazing specification. When you request a quote, ask for the glass type and thickness to be written on it.

Frequently asked questions

Does an aluminium sliding door need safety glass?
Almost always. Sliding door panels are nearly always bigger than 1 m², and glass in a door over 1 m² must be safety glass under SANS 10400-N.
Is 6.38 mm laminated glass safety glass?
Yes. 6.38 mm laminated glass (two 3 mm sheets and a 0.38 mm PVB interlayer) is the most common safety glass used in aluminium doors in South Africa.
Do windows need safety glass?
Only in certain places: where the glass is low (below about 800 mm from the floor) and bigger than 1 m², in bathrooms around showers and baths, and next to stairs and landings. Other windows can use ordinary float glass of the right thickness.
Who is responsible for using the right glass?
The glazier or installer must supply glass that complies, and the building inspector can check it. Ask for the glass type and thickness to be stated on your quote and invoice.

More aluminium door tools

MarkDrawingToolWhat it does
T01Door Panel Layout CalculatorPanel count, panel width and clear opening for sliding, stacking, folding and French doors, drawn to scale.Open
T02Opening Measuring CalculatorTurn three widths, three heights and two diagonals into an order size, and check the opening is square.Open
T03Glass Weight and Roller CalculatorWeight of a glass door panel by size and glass type, and the roller rating it needs.Open
T05Door and Window Schedule BuilderList every opening with size, type, colour and glass, then print it or send it as one quote request.Open
Get a free quote